Painting A Glock - Whether you're on a tight budget, or getting ready for a big project, getting a custom paint job for your gun has never been easier.
For the DIY enthusiast gunsmith, the best metal finish is to spray paint the stock or grip. Spray coating is easier to handle than traditional methods like heat bluing, which requires the use of many tools and harsh chemicals.
Painting A Glock
Spray paints come in a variety of colors and finishes and can be applied to any material. They protect gun metal from rust and act as a barrier against corrosive substances.
How To Paint A Glock Frame?
Spray coating has become the standard for many custom builders of shotguns, tactical guns or target guns. The bluing is traditional and has some visual appeal, but for a working gun that sees a lot of field time, the spray coating makes more sense. It's cheaper, protects the firearm, camouflages it in the field, and is easy to repair or maintain.
They are also good for your love life. Unless you're a solitary hermit, try installing a blowdown tank on your kitchen stove, I dare you! Let me know how it works.
Before you can tinker with any firearm, you must take it apart. Make sure it's not loaded, and take some pictures before starting to help with recovery. Remove all butt stocks, grips, sights, scopes and scope brackets. Taking the gun apart as much as possible is the best and easiest thing to do.
All parts must be cleaned and degreased. Acetone is very effective for this. Plus, Blakelyn's spray gets into cracks and crevices really well.
Growing Concerns In Indiana Over 'ghost Guns' & 'glock Switches'
Finally, each part must be cleaned and thoroughly restored with a residue-free drying solvent. From this point forward, do not handle any degreased parts without clean gloves.
The holes should be plugged with conical silicone plugs. Other areas not to be painted should be sealed with paint tape. Always wear a respirator when doing any sandblasting or painting, not a cheap paint mask but a high quality respirator. Safety glasses are a must, as are leather gloves for sandblasting.
Practice it a few times on a piece of cardboard with an airbrush or rattle so you'll know how to get the best results. Using a spray gun or spray gun, adjust the pressure and spray distance recommended for the product you are using. It may take some experimenting with air and mixing colors to get it right. You want a nice, even, thin coat. Use too much and it looks like paint, not gun paint. It will also do one run, which means you will have to clean it and start over. If there is too much air and not enough coats, or too far from the coat, the atomized paint may partially dry before coating the metal. This results in a rough, matte finish that is not durable. So, practice, practice, practice; then spray your gun.
Further preparation will depend on your resources. Each of these is covered in the next three sections. Of course, the end result will be reflected in the level of work you put into your gun.
Two Toned Glock 19 Featuring Titanium
To be clear, the best way to apply a spray coating is to prepare the metal by sandblasting. This roughens up the surface so the paint will adhere better. The best coats are applied by spraying with an adjustable spray gun operated by an air compressor.
However, I understand that DIY is not always possible in this case. Don't worry, you can refinish your firearm without sandblasting or airbrush, and the results will be amazing.
DuraCoat and Brownells Aluma-Hyde II air-dry coatings can be used on rattle jars. Rattle jars are named for the metal balls inside the jar that mix the liquid and make a distinctive "rattle" sound when you shake the jar. These cans are pressurized like any can spray paint and they give a nice air dry coat on the gun.
Some products can be used on old finishes, but many cannot. Check out the description for each product. DuraCoat says you can use a Scotch-Brite pad to roughen the metal and then spray on the reduced metal. I did this and it worked fine.
How To Paint A Gun
DuraCoat also has a new product called No Sand. After degreasing, using a Scotch-Brite pad to apply No Sand to all metal surfaces will help prepare the surface for final DuraCoat application.
Prepare a low surface. Use painter's tape to drill holes and close off other areas you don't want to paint. Glue the parts from the wires. Always practice on some scrap material to get a feel for spray volume and pattern. Spray thinly on paint. It is better to use a very thin coat than a thick coat. Follow the instructions for any recoating.
Once the part is coated to your satisfaction, it can be hung and cured. Follow the recommended processing time on the can. Do not handle parts prior to recommended cure time.
With gun paint, like most things in life, preparation is everything. The best results will come from metal blasting. One way is to find a metal shop near you and pay them to blast the parts. If you do this, make sure to reduce the metal as you can't guarantee the accuracy of its blasting medium.
Paint Splatter Themed Glock 22 Pistol Cerakoted Using Black Cherry And Pink Champagne
Or, you can buy equipment and do it yourself. Of course, you'll need an air compressor with a tank large enough to maintain pressure while jetting.
The best way to do this is with a sandblasting cabinet. However, you can use an inexpensive gravity feed blasting gun. Before I bought cabinets, I used my handheld sandblasting machine in a 55 gallon plastic bucket to collect the cut sand for reuse, or consider the abrasive a consumable and buy more. Either way, do it outside as you don't want abrasive dust in your shop. Always wear a respirator, safety glasses, and heavy gloves. Don't think you can get by without gloves; sooner or later you'll screw up and blow your arm off. Without gloves, it hurts.
Grit blast the parts with 100 grit aluminum oxide. Use 80 to 100 psi for metal and 30-40 psi for non-metallic parts such as wood, fiberglass, plastic or polymer. Anodized aluminum parts require only 30-40 psi. It is not necessary to remove the anodizing, but you should resurface it.
After the explosion, nothing should be shiny; all parts should have an even matte finish. If there is any flash in any part, hit it again.
Why Cerakote When You Can Spray Paint?
Obviously, if you do sandblasting, you need an air compressor. Given this, it's best to buy a spray gun as well. Paints come in a variety of air dry options. Some of the most popular include DuraCoat, Cerakote, and Gun Coat. They are suitable for HVLP type spray guns with 0.8 mm nozzles.
Spray guns allow you more options when choosing paint and more control over spraying as you work. Airbrush is not very expensive. You can find them online starting at around $15. Mine is $50 and has lasted four years, with many projects done so far.
Professionals use heat-treated coatings. Not only is the time from painting to assembly much shorter, but the heat-treated coating is perceived as a more durable end product.
Baking products include Cerakote H and Elite, DuraBake from DuraCoat, Brownells, Gun-Kote and Teflon/Moly. This list works with many others on the market, but these are the ones I have some experience with. If the part is going into the oven, it's a good idea to mask off any uncoated areas with heat-resistant tape.
Battle Worn Finish Done At Home Without Paint, Froglube And Sandpaper
If you plan to use heat-cure paint, I strongly recommend that you read the instructions and follow the advice contained therein. There are always some differences in the process.
Most oven cured products require some time to flash off some of the chemicals before putting the coated part in the oven. The key is not to let them touch anything. One small bump or brush and you will have to do it all over again.
A few words on this. Always have a bucket of solvent on hand for emergencies. You will have some, so use the recommended solvent to remove the spray coating and start over.
For smaller portions, a convection oven does a good job of "cooking" the coating. I added an oven thermometer for me so I can better control the heat. I also have some magnetic hooks that stick to the top and are great for hanging things.
Painting Glock Frame
If you want to bake
How much for a glock, what is a glock 19, glock a, holster for a glock 19, hunting with a glock, how to hold a glock, how to draw a glock, painting glock frame, how to decock a glock, cleaning a glock 17, what is a glock, glock painting services
0 Comments